PATTON ELECTRONICS COMPANY
1060
|
Card Type |
Modem |
|
Chip Set |
Unidentified |
|
I/O Options |
Power connector, 25-pin connector, terminal block network interface via RJ-11 connector |
|
Wiring Type |
RJ-11 shielded twisted pair |
|
Topology |
Daisy chain, star |
|
Maximum Data Rate |
115.2Kbps |
|
Data Bus |
External |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Power connector |
CN1 |
Network interface via RJ-11 connector |
CN4 | |||
|
Terminal block |
CN2 |
Loopback test switch |
SW1 | |||
|
DTE/DCE serial port (25-pin connector) |
CN3 | |||||
|
USER CONFIGURABLE SETTINGS | ||
|
Setting |
Label |
Position |
|
í Factory configured - do not alter |
SW1/8 |
Unidentified |
|
DTE/DCE | ||
|
Function |
SW3 |
SW4 |
|
DTE (modem or multiplexer) |
On |
On |
|
DCE (PC, terminal or host) |
Off |
Off |
|
DCE MODE PARAMETERS | ||||||||||||||||||||||||||||
|
Control in |
Control out |
Voltage out |
Carrier Control |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
SW1/5 |
SW1/6 |
SW1/7 | ||||||||||||||||||
|
4 |
8 |
6 |
Disabled |
On |
On |
On |
Off |
Off |
Off |
Off | ||||||||||||||||||
|
4 |
8 |
6 |
Enabled |
On |
On |
On |
Off |
Off |
Off |
On | ||||||||||||||||||
|
4, 11, 20 |
8 |
6 |
Disabled |
Off |
On |
On |
On |
Off |
Off |
Off | ||||||||||||||||||
|
4, 11, 20 |
8 |
6 |
Enabled |
Off |
On |
On |
On |
Off |
Off |
On | ||||||||||||||||||
|
4 |
6 |
8 |
Disabled |
On |
Off |
Off |
Off |
On |
On |
Off | ||||||||||||||||||
|
4 |
6 |
8 |
Enabled |
On |
Off |
Off |
Off |
On |
On |
On | ||||||||||||||||||
|
4, 11, 20 |
6 |
8 |
Disabled |
Off |
Off |
Off |
On |
On |
On |
Off | ||||||||||||||||||
|
4, 11, 20 |
6 |
8 |
Enabled |
Off |
Off |
Off |
On |
On |
On |
On | ||||||||||||||||||
|
Note: |
Multiple input pins are "or-tied." If input goes low, carrier is dropped. Multiple output pins generate the same signal simultaneously | |||||||||||||||||||||||||||
|
DTE MODE PARAMETERS | ||||||||||||||||||||||||||||||
|
Control in |
Control out |
Voltage out |
Carrier Control |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
SW1/5 |
SW1/6 |
SW1/7 | ||||||||||||||||||||
|
8 |
4 |
11, 20 |
Disabled |
On |
On |
On |
Off |
Off |
Off |
Off | ||||||||||||||||||||
|
8 |
4 |
11, 20 |
Enabled |
On |
On |
On |
Off |
Off |
Off |
On | ||||||||||||||||||||
|
5, 6, 8 |
4 |
11, 20 |
Disabled |
Off |
On |
On |
On |
Off |
Off |
Off | ||||||||||||||||||||
|
5, 6, 8 |
4 |
11, 20 |
Enabled |
Off |
On |
On |
On |
Off |
Off |
On | ||||||||||||||||||||
|
8 |
11, 20 |
4 |
Disabled |
On |
Off |
Off |
Off |
On |
On |
Off | ||||||||||||||||||||
|
8 |
11, 20 |
4 |
Enabled |
On |
Off |
Off |
Off |
On |
On |
On | ||||||||||||||||||||
|
5, 6, 8 |
11, 20 |
4 |
Disabled |
Off |
Off |
Off |
On |
On |
On |
Off | ||||||||||||||||||||
|
5, 6, 8 |
11, 20 |
4 |
Enabled |
Off |
Off |
Off |
On |
On |
On |
On | ||||||||||||||||||||
|
Note: |
Multiple input pins are "or-tied." If input goes low, carrier is dropped. Multiple output pins generate the same signal simultaneously | |||||||||||||||||||||||||||||
|
MULTIPOINT TOPOLOGY | |||||||||||||||||||
|
Setting |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
SW1/5 |
SW1/6 |
SW1/7 | ||||||||||||
|
Master positions |
On |
On |
On |
Off |
Off |
Off |
Off | ||||||||||||
|
Slave positions |
On |
On |
On |
Off |
Off |
Off |
On | ||||||||||||
|
Note: These settings are used when the device is daisy-chained | |||||||||||||||||||
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
PWR |
Green |
On |
Power is on |
|
PWR |
Green |
Off |
Power is off |
|
TD |
Red |
On |
Low RS-232 logic level |
|
TD |
Red/Green |
Blinking |
Data is being transmitted (high logic level) |
|
TD |
None |
Off |
Data is not being transmitted |
|
RD |
Red |
On |
Low RS-232 logic level |
|
RD |
Red/Green |
Blinking |
Data is being received (high logic level) |
|
RD |
None |
Off |
Data is not being received |
|
IN |
Red |
On |
Low signal detected on control input (pins vary according to switch selection) |
|
IN |
Green |
On |
High signal detected on control input pins |
|
IN |
None |
Off |
No signal being detected on control input pins |
|
OUT |
Red |
On |
Low signal detected on control output (pins vary according to switch selection) |
|
OUT |
Green |
On |
High signal detected on control output pins |
|
OUT |
None |
Off |
No signal being detected on control input pins |
|
TST |
Red |
On |
Device is conducting LAL, or RAL test (depress switch to run test) |
|
TST |
Red |
Off |
Device is not conducting a test |