Card Type	Fax, Modem (synchronous/asynchronous)
Chip Set	Unidentified
I/O Options	Speakerphone, Voice-mail
Maximum Data Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	External
Fax Class	Class I & II
Data Modulation Protocol	Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29, V.33
Error Correction/Compression	MNP5, V.42, V.42bis

CONNECTIONS
Function	Label		Function		Label
Line out		CN1		RS-232/422		CN5
Line in		CN2		DC power		CN6
Microphone in		CN3		Power switch		SW1
Speaker out		CN4

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
AA	Red	On	Auto-answer enabled
AA	Red	Off	Auto-answer disabled
AA	Red	Blinking	Phone is ringing
CD	Red	On	Carrier signal detected
CD	Red	Off	Carrier signal not detected
OH	Red	On	Modem is off-hook
OH	Red	Off	Modem is on-hook
IO	Red	On	Modem is transmitting or receiving data
IO	Red	Off	Modem is not transmitting or receiving data
MR	Red	On	Power is on
MR	Red	Off	Power is off

AUTO-RELIABLE TIME BUFFER CONFIGURATION
Type:	Configuration
Format:	AT [cmds] \Cn [cmds]
Description:	Controls the handling of incoming data during auto-reliable time period
Command	Function
\C0	Data is discarded
\C1	Data is buffered
\C2	Data is discarded; modem returns to normal mode on receiving auto-reliable fallback character.

AUTO-RETRAIN
Type:	Configuration
Format:	AT [cmds] %En [cmds]
Description:	Controls auto-retrain mode
Command	Function
%E0	Auto-retrain disabled
%E1	Auto-retrain enabled

BREAK TYPE
Type:		Configuration
Format:		AT [cmds] \Kn [cmds]
Description:		Configures action of break signal
Command	Break from DTE
\K0	Online command mode enabled, send no break to remote modem
\K1	Break sent to remote modem and buffered cleared
\K2	Online command mode enabled, send no break to remote modem
\K3	Send break to remote modem immediately
\K4	Online command mode enabled, send no break to remote modem
\K5	Send break with transmitted data

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %Cn [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
%C1	MNP5 enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	MNP reliable mode enabled
\N3	Auto-reliable mode enabled
\N4	V.42 reliable mode enabled
\N5	V.42 auto-reliable mode enabled
\N6	Reliable mode enabled

DICTIONARY SIZE
Type:	Configuration
Format:	AT [cmds] %Dn [cmds]
Description:	Select dictionary size
Command	Function
%D0	Select 1/2K dictionary
%D1	Select 1K dictionary
%D2	Select 2K dictionary

ERROR CONTROL BUFFER - MAXIMUM
Type:	Register
Format:	AT [cmds] S50=n [cmds]
Default:	200
Range:	0-255
Unit:	Unidentified
Description:	Controls the maximum size of the error control buffer

ERROR CONTROL BUFFER - MINIMUM
Type:	Register
Format:	AT [cmds] S49=n [cmds]
Default:	10
Range:	0-255
Unit:	Unidentified
Description:	Controls the minimum size of the error control buffer

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] \Gn [cmds]
Description:	Selects modem port flow control
Command	Function
\G0	Flow control disabled
\G1	Flow control enabled

FLOW CONTROL - HARDWARE
Type:	Configuration
Format:	AT [cmds] \Ln [cmds]
Description:	Selects the transfer mode for MNP link
Command	Function
\L0	Hardware flow control enabled (used for Mac with standard Mac modem cable)
\L1	Hardware flow control disabled (used for PC or Mac with hardware flow-control cable)

FLOW CONTROL TYPE
Type:	Configuration
Format:	AT [cmds] \Qn [cmds]
Description:	Sets type of flow control used by modem
Command	Function
\Q0	Flow control disabled
\Q1	Bi-directional XON/XOFF flow control and bi-directional RTS/CTS enabled
\Q2	CTS flow control by DCE enabled
\Q3	Bi-directional RTS/CTS flow control enabled
\Q4	Unidirectional XON/XOFF flow control by DCE enabled

MNP RESULT CODES
Type:	Configuration
Format:	AT [cmds] \Vn [cmds]
Description:	Selects MNP result codes
Command	Function
\V0	MNP result codes disabled
\V1	MNP result codes enabled

INACTIVITY TIMER
Type:	Configuration
Format:	AT [cmds] \Tn [cmds]
Default:	0
Range:	0-90
Unit:	1 minute
Description:	Sets the length of time that the modem does not receive information before it disconnects.

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports 3 digit product code
I1	Reports ROM checksum
I2	Reports OK
I3	Reports firmware version
I4	Reports configuration settings

XON/XOFF PASS-THROUGH
Type:	Configuration
Format:	AT [cmds] \Xn [cmds]
Description:	Selects whether XON/XOFF signals are sent to remote modem
Command	Function
\X0	XON/XOFF signals trapped by local modem
\X1	XON/XOFF passed through local modem