MULTIWAVE INNOVATION, INC
CW56ES
|
Card Type |
Modem (synchronous/asynchronous), Voice |
|
Chipset |
Unidentified |
|
Maximum Modem Rate |
56.0Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Fax Class |
Class I & II |
|
Modem Modulation Protocol |
Bell 103A/212A ITU-T V.21, V.22, V.22bis,V.32, V.32bis, V.34bis |
|
Fax Modulation Protocol |
ITU-T V.17, V.21 CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Data Bus |
16-bit ISA |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Line out |
CN1 |
Speaker connector |
CN3 | |||
|
Line in |
CN2 | |||||
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, A/ |
|
A, B, E, H, L, M, P, Q, T, V, W, X, Z |
|
&C, &V, &W |
|
Extended AT Commands |
|
\A, \G, \L, \N |
|
%C |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S22, S29, S32, S33, S95 |
|
Special Commands |
|
#CID |
|
Voice Commands |
|
#MDL?, #MFR?, #REV?, #VRX, #VTS, #VTX |
|
Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
|
AUTO-MODE DETECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Nn [cmds] |
|
Description: |
Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. |
|
Command |
Function |
|
N0 |
Auto-mode detection disabled. Handshake begins at line speed designated by the S37 register or if S37=0, at last DTE speed |
|
N1 |
Auto-mode detection enabled. Handshake conducted according to the automode algorithm supported by the modem |
|
COMMUNICATIONS MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Mn [cmds] |
|
Description: |
Selects communications mode |
Note: Command non-functional; for compatibility purposes only. Returns OK. | |
|
COMMUNICATIONS MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Qn [cmds] |
|
Description: |
Selects communications mode options |
Note: Command non-functional; for compatibility purposes only. Returns OK. | |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
Note: Command non-functional; for compatibility purposes only. Returns OK. | |
|
DATA TERMINAL READY (DTR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Dn [cmds] |
|
Description: |
Selects modem response to DTR |
|
Command |
Function |
|
? &D0 |
DTR forced high |
|
&D1 |
DTR toggle causes online command mode |
|
&D2 |
Normal DTR operations |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
DL |
Re-dial last number |
|
DP |
Pulse dialing enabled |
|
DSn |
Dial stored telephone number n |
|
DT |
Tone dialing enabled/Pulse dialing disabled |
|
DW |
Dialing resumed following dial tone detection |
|
D, |
Dialing paused for amount of time specified in S8 register |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
FACTORY DEFAULT PROFILE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &F [cmds] |
|
Description: |
Sets values in active profile to values found in the default profile |
|
Command |
Function |
|
&F0 |
Restore factory configuration 0 |
|
&F1 |
Restore factory configuration 0 |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Enables flow control options |
|
Command |
Function |
|
&K0 |
Flow control disabled |
|
&K3 |
RTS/CTS flow control enabled |
|
&K4 |
XON/XOFF flow control enabled |
|
&K5 |
Transparent XON/XOFF flow control enabled |
|
&K6 |
Both RTS/CTS & XON/XOFF flow control enabled |
|
JACK TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Jn [cmds] |
|
Description: |
Selects jack type |
Note: Command non-functional; for compatibility purposes only. Returns OK. | |
|
LINE TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Ln [cmds] |
|
Description: |
Selects line type |
Note: Command non-functional; for compatibility purposes only. Returns OK. | |
|
LONG SPACE DISCONNECT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Yn [cmds] |
|
Description: |
Commands the modem to disconnect after a 1.6 second break is detected |
Note: Command non-functional; for compatibility purposes only. Returns result code. | |
|
ON-LINE | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] On [cmds] |
|
Description: |
Controls on-line command (data transmission) state options. |
Note: The O command must be placed at the end of the command string. | |
|
Command |
Function |
|
O0 |
On-line command mode with no retraining enabled |
|
O1 |
On-line command mode with long retrain enabled |
|
O2 |
On-line command mode with short retrain enabled |
|
PULSE DIALING RATIO | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Pn [cmds] |
|
Description: |
Selects pulse dial make/break ratio |
|
Command |
Function |
|
? &P0 |
39/61ms at 10pps (North America) |
|
&P1 |
33/67ms at 10pps (Europe) |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports product code |
|
I1 |
Reports hardware variation |
|
I2 |
Reports DSP firmware revision model code |
|
I3 |
Reports controller firmware revision model code |
|
I4 |
Reports manufacturer and model information |
|
RESTORE PROFILE ON POWER-UP | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Yn [cmds] |
|
Description: |
Restores a selected profile into the active profile on power-up (hard reset) |
Note: Command non-functional; for compatibility purposes only. Returns OK. | |
|
TEST MODES | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] &Tn |
|
Description: |
Selects test options |
|
Command |
Function |
|
&T0 |
End current test |
|
&T1 |
Begin local analog loopback test |
|
TRANSMIT CARRIER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Cn [cmds] |
|
Description: |
Controls the transmit carrier switching |
Note: Command non-functional; for compatibility purposes only. Returns result code. | |
EXTENDED AT COMMAND SET
|
AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %En [cmds] |
|
Description: |
Controls auto-retrain mode and fallback/fall-forward |
|
Command |
Function |
|
%E0 |
Auto-retrain disabled |
|
? %E1 |
Auto-retrain enabled |
SPECIAL COMMANDS
|
BLACKLISTED NUMBERS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *Bn [cmds] |
|
Description: |
Displays numbers which failed the last call attempt within two hours. In countries that do not require blacklisting, command returns ERROR |
|
CALLING TONE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *Cn [cmds] |
|
Description: |
Controls whether the DTE will allow the modem to send a 1300Hz calling tone when originating |
|
Command |
Function |
|
*C0 |
Disable calling tone |
|
*C1 |
Enable calling tone |
|
COUNTRY SELECT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *NCn [cmds] |
|
Description: |
Selects up to 7 country parameters |
|
Command |
Function |
|
*NC0 |
United States |
|
*NC1 |
Japan |
|
*NC2 |
Germany |
|
*NC3 |
United Kingdom |
|
*NC4 |
France |
|
*NC5 |
Netherlands |
|
*NC6 |
Italy |
|
DELAYED NUMBERS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *Dn [cmds] |
|
Description: |
Displays delayed numbers with lag associated with each number |
|
SINGLE/DUAL TONE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *Sn [cmds] |
|
Description: |
Selects single or dual tone |
|
Command |
Function |
|
*S0 |
Regular dual tone transmitted to line |
|
*S1 |
Low band tone transmitted to line |
|
*S2 |
High band tone transmitted to line |
|
MODULATION SELECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] +MS=x,y,z,a [cmds] |
|
Description: |
Sets options for active protocol; the transfer rates specified by z and a must be valid for the protocol selected. |
|
Command |
Function |
|
x=0 |
V.21 |
|
x=1 |
V.22 |
|
x=2 |
V.22bis |
|
x=3 |
V.23 |
|
x=9 |
V.32 |
|
x =10 |
V.32bis |
|
x=11 |
V.34 |
|
x =64 |
Bell 103 |
|
x =69 |
Bell 212A |
S(status) REGISTERS
|
BIT-MAPPED REGISTER S14 | ||
|
Format: |
AT [cmds] S14=n [cmds] | |
|
Range: |
0-174 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls echo, result codes and display, dial mode, and answer/originate mode. | |
|
Bit |
Value |
Function |
|
0 |
0 |
Not used |
|
1 |
0 1 |
Command echo disabled Command echo enabled |
|
2 |
0 1 |
Result codes enabled Result codes disabled |
|
3 |
0 1 |
Display result codes in numeric format Display result codes in verbose format |
|
4 |
0 |
Not used |
|
5 |
0 1 |
Tone dial enabled Pulse dial enabled |
|
6 |
0 |
Not used |
|
BIT-MAPPED REGISTER S21 | ||
|
Format |
AT [cmds] S21=n [cmds] | |
|
Range: |
0-253 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Selects jack type, CTS/DCD/DSR signals, and low DTR action | |
|
Bit |
Value |
Function |
|
0 |
0 1 |
Selects RJ-11, RJ-41S, or RJ45S jack Selects RJ-12 or RJ-13 jack |
|
1 |
0 |
Not used |
|
2 |
0 |
Not used |
|
4, 3 |
00 01 10 |
DTR forced high DTR toggle causes online command mode Normal DTR operations |
|
5 |
0 |
Not used |
|
6 |
0 |
DSR bahavior (not used) |
|
7 |
0 |
Not used |
|
BIT-MAPPED REGISTER S27 | ||
|
Format |
AT [cmds] S27=n [cmds] | |
|
Range: |
0-111 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Selects synchronous/asynchronous mode, line type, clock source, and ITU-T/Bell modes. | |
|
Bit |
Value |
Function |
|
3, 1, 0 |
00 01 10 |
Asynchronous mode, serial port speed follows connect speed Error corrected mode Buffered asyncronous mode |
|
2, 4-7 |
0 |
Not Used |
|
BIT-MAPPED REGISTER S28 | ||
|
Format |
AT [cmds] S28=n [cmds] | |
|
Range: |
0-31 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls transmit/receive speed, MNP link negotiation speed | |
|
Bit |
Value |
Function |
|
0-2 |
0 |
Not Used |
|
4, 3 |
00 01 10 11 |
39ms make/61ms break at 10pps 33ms make/67ms break at 10pps 39ms make/61ms break at 20pps 33ms make/67ms break at 20pps |
|
7, 6 |
00 01 10 |
MNP link negotiation at highest possible speed MNP link negotiation at 1200bps MNP link negotiation at 4800bps |
|
BIT-MAPPED REGISTER S31 | |||
|
Format: |
AT [cmds] S31=n [cmds] | ||
|
Range: |
0-10 | ||
|
Description: |
Select line speed detection | ||
|
Bit |
Value |
Function | |
|
0 |
0 |
Not used | |
|
1 |
0 1 |
Line speed auto-detection disabled Line speed auto-detection enabled | |
|
2-7 |
0 |
Not used | |
|
BIT-MAPPED REGISTER S40 | ||
|
Format |
AT [cmds] S40=n [cmds] | |
|
Range: |
0-255 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls power level and break handling; selects MNP extended services, link negotiation, and block size. | |
|
Bit |
Value |
Function |
|
0-1 |
0 |
Not Used |
|
2 |
0 |
Not Used |
|
5, 4, 3 |
0 |
Not Used |
|
7, 6 |
? 0001 10 11 |
MNP block size is 64 characters MNP block size is 128 characters MNP block size is 192 characters MNP block size is 256 characters |
|
BIT-MAPPED REGISTER S41 | ||
|
Format |
AT [cmds] S41=n [cmds] | |
|
Range: |
0-31 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Selects compression, auto-retrain, flow control, and MNP mode. | |
|
Bit |
Value |
Function |
|
1 - 0 |
00 01 10 11 |
Data compression disabled MNP5 enabled V.42bis enabled MNP5 and V.42bis enabled |
|
2 |
0 |
Not Used |
|
3 |
0 1 |
Flow control disabled Flow control enabled |
|
4 |
0 1 |
Stream mode for MNP Block mode for MNP |
|
5-7 |
0 |
Not Used |
|
CONNECTION FAILURE CODES | |
|
Type: |
Register |
|
Format |
AT [cmds] S86? [cmds] |
|
Description: |
Reports codes which correspond to the possible causes of a connection failure |
|
Value |
Meaning |
|
0 |
Normal hang up |
|
4 |
Carrier signal lost |
|
9 |
No common protocol found |
|
12 |
No failure - remote modem disconnected normally |
|
13 |
Remote modem failed to respond after 10 re-transmissions same message |
|
14 |
Violation of negotiated protocol caused failure |
|
DCE LINE SPEED | |
|
Type: |
Register |
|
Format |
AT [cmds] S37=n [cmds] |
|
Description: |
Sets the maximum allowable data exchange rate attempted during handshake process. |
|
Command |
Function |
|
? S37=0 |
Attempt an automode connection |
|
S37=1 |
300bps |
|
S37=2 |
300bps |
|
S37=3 |
300bps |
|
S37=4 |
Reserved |
|
S37=5 |
V.22 at 1200bps |
|
S37=6 |
V.22 at 2400bps |
|
S37=8 |
V.32bis at 4800bps |
|
S37=7 |
Reserved |
|
S37=9 |
V.32bis at 9600bps |
|
S37=10 |
V.32bis at 12.0Kbps |
|
S37=11 |
V.32bis at 14.4Kbps |
|
S37=12 |
V.32bis at 7200bps |
|
S37=13 |
Reserved |
|
S37=14 |
Reserved |
|
S37=15 |
V.34 at 14.4Kbps |
|
S37=16 |
V.34 at 16.8Kbps |
|
S37=17 |
V.34 at 19.2Kbps |
|
S37=18 |
V.34 at 21.6Kbps |
|
S37=19 |
V.34 at 24.0Kbps |
|
S37=20 |
V.34 at 26.4Kbps |
|
S37=21 |
V.34 at 28.8Kbps |
|
S37=22 |
V.34 at 33.6Kbps |
|
ERROR CORRECTION/COMPRESSION | |||
|
Type: |
Register | ||
|
Format: |
AT [cmds] S46=n [cmds] | ||
|
Description: |
Selects active error correction and compression protocols | ||
|
S46=136 |
LAP-M only, no compression | ||
|
S46=138 |
LAP-M with V.42bis data compression | ||
|
FLOW CONTROL | |
|
Type: |
Register |
|
Format |
AT [cmds] S39? [cmds] |
|
Description: |
Displays the current flow control |
|
Value |
Meaning |
|
0 |
Flow control disabled |
|
1 |
RTS/CTS flow control enabled |
|
2 |
XON/XOFF flow control enabled |
|
3 |
Transparent XON/XOFF flow control enabled |
|
4 |
Both RTS/CTS & XON/XOFF flow control enabled |
|
TEST MODES | ||
|
Type: |
Register | |
|
Format: |
AT [cmds] S16=n [cmds] | |
|
Range: |
0-125 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls loopback tests, analog, digital, remote digital, and self tests. | |
|
Bit |
Value |
Function |
|
0 |
0 1 |
Local analog loopback disabled Local analog loopback enabled |
|
1 |
0 |
Not used |
|
2 |
0 1 |
Local digital loopback disabled Local digital loopback enabled |
|
3-7 |
0 |
Not used |
|
TIES/HAYES | |||
|
Type: |
Register | ||
|
Format: |
AT [cmds] S68=n [cmds] | ||
|
Description: |
Selects TIES/Hayes | ||
|
Command |
Function | ||
|
S68=0 |
TIES enabled | ||
|
S68=1 |
Hayes escape sequence enabled | ||
|
TRANSMISSION LEVEL - DATA | |
|
Type |
Register or Configuration |
|
Format |
AT [cmds] S91=n [cmds] |
|
Range |
6-15 |
|
Unit |
-1dBm |
|
Default |
10 |
|
Description |
Sets the signal level for data transmission |
|
TRANSMISSION LEVEL - FAX | |
|
Type |
Register or Configuration |
|
Format |
AT [cmds] S92=n [cmds] |
|
Range |
6-15 |
|
Unit |
-1dBm |
|
Default |
10 |
|
Description |
Sets the signal level for fax transmission |
VOICE COMMANDS
|
AEC/SPEAKERPHONE | |||
|
Type: |
Configuration | ||
|
Format: |
AT [cmds] +VSP=n [cmds] | ||
|
Description: |
Controls AEC/speaker phone. +VSP=? queries setting | ||
|
Command |
Function | ||
|
+VSP=0 |
Unidentified | ||
|
+VSP=1 |
Unidentified | ||
|
AUTOMATIC HANG-UP CONTROL | |||
|
Type: |
Configuration | ||
|
Format: |
AT [cmds] +VNH=n [cmds] | ||
|
Description: |
Controls hang-ups in non-voice mode. +VNH=? queries setting | ||
|
Command |
Function | ||
|
+VNH=0 |
Normal hang-up | ||
|
+VNH=1 |
DCE initiated hang-ups are disabled in non-voice modes | ||
|
+VNH=2 |
Logical hang-up. Automatic hang-up is disabled but OK result will be issued to hang-up command in non-voice modes | ||
|
EVENT REPORTING AND MASKING | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] +VEM=n [cmds] |
|
Default: |
FFFFFFFF8 |
|
Range: |
Unidentified |
|
Unit: |
Hexadecimal |
|
Description: |
Selects value of event mask to DTE. +VEM=? queries four lines of information, corresponding to the service level, voice transmit state, voice receive state, and voice command state |
|
RECEIVE DATA SOURCE | |||
|
Type: |
Configuration | ||
|
Format: |
AT [cmds] +VRX=n [cmds] | ||
|
Description: |
Enables voice reception process on DCE. | ||
|
Command |
Function | ||
|
VRX=0 |
Voice reception enabled | ||
|
VRX=1 |
Voice reception with DCE periodic tone enabled | ||
|
TONE GENERATOR (PHONE KEYS) | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] +VTS=a |
|
Unit: |
ASCII [0-9, A-D, #, *] |
|
Description: |
Generates the DTMF tone for the characters in the string for the duration set with +VTD. +VTS=? queries values |
|
TONE GENERATOR LENGTH | |
|
Format: |
AT [cmds] +VTD=n [cmds] |
|
Default: |
100 |
|
Range: |
0 - 500 |
|
Unit: |
.01sec |
|
Description: |
Sets the length of DTMF tones that are generated. +VTD=? queries values |
|
VOICE DEVICE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] +VLS=n [cmds] |
|
Description: |
Selects the I/O device for the DSP chip. +VLS=? queries setting |
|
VOICE GAIN - PLAYBACK | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] +VGT=n [cmds] |
|
Range: |
0, 128 |
|
Description: |
Sets the gain for voice playback. |
|
VOICE GAIN - RECORD | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] +VGR=n [cmds] |
|
Range: |
0-128 |
|
Description: |
Sets the gain for received voice signals. A value of 0 sets automatic gain level. |
|
VOICE PARAMETERS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] +VIP=n [cmds] |
|
Description: |
Resets voice parameters to factory default settings. +VIP=? Will display acceptable profiles |
|
VOICE SILENCE DETECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] +VSD=m,n [cmds] |
|
Default: |
m = 128, n =50 |
|
Range: |
m 0-255, n 0-600 |
|
Unit: |
m 1 dB, n .1 second |
|
Description: |
Sets the threshold of silence detection (m) and the minimum period of silence required to be detected (n). +VSD=? queries values |