DANPEX CORPORATION

AN-550S/AN-550BT

NIC Type

ARCnet

Transfer Rate

2Mbps

Data Bus

16-bit ISA

Topology

Star (AN-550S)

Linear Bus (AN-550BT)

Wiring Type

Shielded/Unshielded twisted pair

RG62A/U 93ohm coaxial

Boot ROM

Available

NODE ADDRESS

Node

SW1/1

SW1/2

SW1/3

SW1/4

SW1/5

SW1/6

SW1/7

SW1/8

0

-

-

-

-

-

-

-

-

1

Off

On

On

On

On

On

On

On

2

On

Off

On

On

On

On

On

On

3

Off

Off

On

On

On

On

On

On

4

On

On

Off

On

On

On

On

On

251

Off

Off

On

Off

Off

Off

Off

Off

252

On

On

Off

Off

Off

Off

Off

Off

253

Off

On

Off

Off

Off

Off

Off

Off

254

On

Off

Off

Off

Off

Off

Off

Off

255

Off

Off

Off

Off

Off

Off

Off

Off

Note:Node address 0 is used for messaging between nodes and must not be used.

A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 1 is the Least Significant Bit and switch 8 is the Most Significant Bit. The switches have the following decimal values: switch 1=1, 2=2, 3=4, 4=8, 5=16, 6=32, 7=64, 8=128. Turn off the switches and add the values of the off switches to obtain the correct node address. (On=0, Off=1)

BASE MEMORY ADDRESS & BOOT ROM ADDRESS

Base Address

Boot ROM

SW2/1

SW2/2

SW2/3

SW2/4

SW2/5

 

C0000h

C2000h

On

On

On

On

On

 

C0800h

C2000h

Off

On

On

On

On

 

C1000h

C2000h

On

Off

On

On

On

 

C1800h

C2000h

Off

Off

On

On

On

 

C4000h

C6000h

On

On

Off

On

On

 

C4800h

C6000h

Off

On

Off

On

On

 

C5000h

C6000h

On

Off

Off

On

On

 

C5800h

C6000h

Off

Off

Off

On

On

 

CC000h

CE000h

On

On

On

Off

On

 

CC800h

CE000h

Off

On

On

Off

On

 

CD000h

CE000h

On

Off

On

Off

On

 

CD800h

CE000h

Off

Off

On

Off

On

»

D0000h

D2000h

On

On

Off

Off

On

 

D0800h

D2000h

Off

On

Off

Off

On

 

D1000h

D2000h

On

Off

Off

Off

On

 

D1800h

D2000h

Off

Off

Off

Off

On

 

D4000h

D6000h

On

On

On

On

Off

 

D4800h

D6000h

Off

On

On

On

Off

 

D5000h

D6000h

On

Off

On

On

Off

 

D5800h

D6000h

Off

Off

On

On

Off

 

D8000h

DA000h

On

On

Off

On

Off

 

D8800h

DA000h

Off

On

Off

On

Off

 

D9000h

DA000h

On

Off

Off

On

Off

 

D9800h

DA000h

Off

Off

Off

On

Off

 

DC000h

DE000h

On

On

On

Off

Off

 

DC800h

DE000h

Off

On

On

Off

Off

 

DD000h

DE000h

On

Off

On

Off

Off

 

DD800h

DE000h

Off

Off

On

Off

Off

 

E0000h

E2000h

On

On

Off

Off

Off

 

E0800h

E2000h

Off

On

Off

Off

Off

 

E1000h

E2000h

On

Off

Off

Off

Off

 

E1800h

E2000h

Off

Off

Off

Off

Off

I/O BASE ADDRESS

Address

SW2/6

SW2/7

SW2/8

 

260-26Fh

On

On

On

 

290-29Fh

Off

On

On

»

2E0-2EFh

On

Off

On

 

2F0-2FFh

Off

Off

On

 

300-30Fh

On

On

Off

 

350-35Fh

Off

On

Off

 

380-38Fh

On

Off

Off

 

3E0-3EFh

Off

Off

Off

BOOT ROM

Setting

SW2/9

»

Disabled

Off

 

Enabled

On

ONBOARD TERMINATOR

Setting

SW1/10

»

Disabled

Off

 

Enabled

On

Note:If the card is the last card in the network segment, the onboard terminator must be enabled. If the card

INTERRUPT REQUEST

IRQ

JP2A

JP2B

JP2C

JP2D

JP2E

JP2F

JP2G

JP2H

»

2/9

Closed

Open

Open

Open

Open

Open

Open

Open

 

3

Open

Closed

Open

Open

Open

Open

Open

Open

 

4

Open

Open

Closed

Open

Open

Open

Open

Open

 

5

Open

Open

Open

Closed

Open

Open

Open

Open

 

7

Open

Open

Open

Open

Closed

Open

Open

Open

 

10

Open

Open

Open

Open

Open

Closed

Open

Open

 

12

Open

Open

Open

Open

Open

Open

Closed

Open

 

15

Open

Open

Open

Open

Open

Open

Open

Closed

CABLE TYPE

Type

JP4

JP5

»

RG62A/U 93ohm coaxial

Pins 2 & 3 closed

Pins 2 & 3 closed

 

Shielded/Unshielded twisted pair

Pins 1 & 2 closed

Pins 1 & 2 closed

FACTORY CONFIGURED SETTINGS

Jumper

Setting

JP1

Unused

DIAGNOSTIC LED(S)

LED

Status

Condition

LED1

On

Card is receiving power and is operating properly

LED1

Blinking

Data is being transmitted or received

LED1

Off

Card is not receiving power or is defective

MISCELLANEOUS NOTES

The AN-550S uses a star topology while the AN-550BT uses a linear bus topology. Other than topology, the two cards are identical.