C P - 3 0 5 4 4 CONNER NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 2243| 1023| | Capacity form/unform 545/ MB Heads 6| 16| | Seek time / track 10.0/ 2.0 ms Sector/track | 63| | Controller IDE / AT Precompensation Cache/Buffer 256 KB Landing Zone 1023 Data transfer rate 3.000 MB/S int Bytes/Sector 512 6.000 MB/S ext Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 60 Power: sleep W Humidity % 5 95 | 5 95 standby W Altitude km -0.061 3.048| -0.061 12.192 idle 5.2 W Shock g 5 | 75 seek 9.0 W Rotation RPM 5400 read/write 6.5 W Acoustic dBA 40 spin-up W ECC Bit MTBF h 250000 Warranty Month 24 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** CONNER CP30544 QUICK REFERENCE GUIDE REV. C, 12/1994 +---------------------------------------------------------+ J6 | +-+ |XXPower | | | |xx1 | | |J1 |XXI | | |HDA |XXN | | | |XXT | +-+ E8++++++E2|XXE J2 | ++++++++ |XXR | BLOCK A |XXF | |XXA | |XXC | |XXE |J3-+Spindle Sync |XX | | |LED Drive Capability |XX | | | |XX | | |ATA/ISA ++ | 1 | +-+C/D (Alternate to Jumper Block B) +++++|BLOCK B|XX J4 | xx LED ++++++ |XX Power +---------------------------------------------------------+ 1 ********************************************************************** J U M P E R S ********************************************************************** CONNER CP30544 QUICK REFERENCE GUIDE REV. C, 12/1994 Jumper Setting ============== Jumper Block B -------------- No spin on Power ON +---DASP on pin 39 (DSP) +---+-+-+---+C/D+ o Spin Sync on pin 39 (SS) | o | o | o | o | o | | o | o | o | o | o | +---+---+-+-+---+---+ ATA/ISA C/D --- Up to two drives may be daisy chained together utilizing the 40 pin Task File connector. The maximum cable length is 18 inches. In order to install more than one drive, it is necessary to set a jumper option. The C/D jumper is used to determine whether the drive is master (drive C) or slave (drive D). The drive is configured as a master (drive C) when jumpered and as a slave drive (D drive) when not jumpered. DSP & SS -------- This pair of jumpers determines the signals on pin 39 of the inter- face connector. +---------+----------------------------------------------------+ | Jumper | Action | |DSP SS | | +----+----+----------------------------------------------------+ | X | | - Spindle synchronization signal disable on pin 39 | | | | - Activity LED signal available on pin 39 | +----+----+----------------------------------------------------+ | | X | - Spindle synchronization signal enable on pin 39 | | | | - Activity LED signal disabled from pin 39 | +----+----+----------------------------------------------------+ | | | - Pin 39 floating | +----+----+----------------------------------------------------+ +-----------------+-----------------+ | | Function | +-----------------+--------+--------+ | Jumper |ATA/CAM |Non-CAM | +--------+--------+--------+--------+ |BLOCK A | E2 | OUT | IN | +--------+--------+--------+--------+ |BLOCK A | E3 | OUT | IN | +--------+--------+--------+--------+ |BLOCK A | E4 | OUT | IN | +--------+--------+--------+--------+ |BLOCK A | E5 | IN | OUT | +--------+--------+--------+--------+ |BLOCK A | E6 | IN | OUT | +--------+--------+--------+--------+ |BLOCK A | E7 | IN | OUT | +--------+--------+--------+--------+ |BLOCK A | E8 | IN | OUT | +--------+--------+--------+--------+ |BLOCK B |ATA/ISA | IN | OUT | +--------+--------+--------+--------+ ********************************************************************** I N S T A L L ********************************************************************** CONNER CP30544 QUICK REFERENCE GUIDE REV. C; 12/1994 Notes on Installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive will operate in all axis (6 directions). J4 Standard 4-pin Power Connector --------------------------------- +----------------------- | +-----J4-----+ +---- pin 1 +12V | | 1 2 3 4 | | 1 pin 2 GND | +------------+ +-- pin 3 GND +------------------ pin 4 +5V J6 Alternate 3-pin Power Connector ---------------------------------- +------------------------------ | +--J6---+ +--- pin 1 +5 V | | 3 2 1 | | 40 pin 2 +12V | +-------+ +---- pin 3 GND +----------------------------------