ACCULOGIC, INC.

SIDE-4/HP

Data bus:

16-bit ISA

Size:

Half-length, full-height card

Hard drive supported:

Two IDE(AT) interface drives

Floppy drives supported:

Two 360KB, 720KB, 1.2MB, 1.44MB or 2.88MB drives

CONNECTIONS

Function

Location

34-pin cable connector - floppy drive

J5

40-pin IDE(AT) connector

J6

10-pin serial port 2 - internal

J7

9-pin serial port 1 - external

J9

25-pin parallel port - external

J10

4-pin connector - drive active LED

J12

Internal power connector

J13

USER CONFIGURABLE SETTINGS

Function

Location

Setting

»

IDE primary address enabled

JP2

Pins 2 & 3 closed

 

IDE secondary address is 170h

JP2

Pins 1 & 2 closed

»

IDE(AT) interface enabled

JP3

Pins 1 & 2 closed

 

IDE(AT) interface disabled

JP3

Pins 2 & 3 closed

»

Factory configured - do not alter

JP6

N/A

»

Factory configured - do not alter

JP7

N/A

»

Floppy primary address enabled

JP9

Pins 2 & 3 closed

 

Floppy secondary address enabled

JP9

Pins 1 & 2 closed

 

Floppy secondary address enabled

JP9

Pins 1 & 2 closed

USER CONFIGURABLE SETTINGS (CONTINUED)

Function

Location

Setting

»

Factory configured - do not alter

JP11

N/A

»

Factory configured - do not alter

JP12

N/A

»

Floppy drive interface enabled

JP15

Pins 1 & 2 closed

 

Floppy drive interface disabled

JP15

Pins 2 & 3 closed

»

Parallel port IRQ 7 select

JP16

Pins 1 & 2 closed

 

Parallel port IRQ 5 select

JP16

Pins 2 & 3 closed

»

IOCHRDY signal disabled

JP17

Open

 

IOCHRDY signal enabled

JP17

Closed

 

IDE(AT) IRQ 15 select - normal

JP18

Pins 1 & 2 closed

 

IDE(AT) IRQ15 select - delayed

JP18

Pins 2 & 3 closed

»

IDE(AT) IRQ 14 select - normal

JP19

Pins 1 & 2 closed

 

IDE(AT) IRQ14 select - delayed

JP19

Pins 2 & 3 closed

»

Serial port 1 IRQ4 select

JP22

Pins 1 & 2 closed

»

Serial port 2 IRQ3 select

JP22

Pins 3 & 4 closed

Note: The location of jumper JP17 is unidentified. It may be soldered on the board in some models.

SERIAL PORT 1 ADDRESS SELECTION

COM

JP8

JP14

»

COM1 (3F8h)

Pins 1 & 2 closed

Pins 1 & 2 closed

 

COM2 (2F8h)

Pins 1 & 2 closed

Pins 2 & 3 closed

 

COM3 (2F8h)

Pins 2 & 3 closed

Pins 1 & 2 closed

 

Disabled

Pins 2 & 3 closed

Pins 2 & 3 closed

SERIAL PORT 2 ADDRESS SELECTION

COM

JP10

JP13

»

COM2 (2F8h)

Pins 1 & 2 closed

Pins 1 & 2 closed

 

COM1 (3F8h)

Pins 1 & 2 closed

Pins 2 & 3 closed

 

COM4 (238h)

Pins 2 & 3 closed

Pins 1 & 2 closed

 

Disabled

Pins 2 & 3 closed

Pins 2 & 3 closed

PARALLEL PORT ADDRESS SELECTION

LPT

JP4

JP5

»

LPT1(378h)

Pins 1 & 2 closed

Pins 2 & 3 closed

 

LPT2(278h)

Pins 1 & 2 closed

Pins 1 & 2 closed

 

Disabled

Pins 2 & 3 closed

Pins 2 & 3 closed

PARALLEL PORT DMA SELECTION

Channel

JP20

JP21

1

Pins 1 & 2 closed

Pins 1 & 2 closed

3

Pins 2 & 3 closed

Pins 2 & 3 closed

MISCELLANEOUS TECHNICAL NOTES

Location of pin 1 on all jumpers is not available.