ACER, INC.

MAGIC MP32

Card Type

Modem, Fax, Sound card

Chip Set

Unidentified

I/O Options

CD-ROM interface, microphone, audio line in, audio line out, wavetable interface

Maximum Modem Rate

33.6Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation Protocol

Bell 103/212A

ITU-T V.22, V.22bis, V.23, V.32, V.32bis, V.34, V.34bis

Fax Modulation Protocol

ITU-T V.17, V.21CH2, V.27ter, V.29, V.33

Error Correction/Compression

MNP5, V.42, V.42bis

Fax Class

Class I & II

Data Bus

16-bit ISA

Card Size

Full-length, full-height card

CONNECTIONS

Function

Label

Function

Label

MIDI/Game port

CN1

Wave table interface

CN6

Telephone line in

CN4

Speaker/Line out

CN7

Telephone line out

CN5

Line in

CN8

Microphone in

CN9

CD-Audio

JP5

SPEAKER/LINE OUT SETTINGS

Function

CN2

CN3

Speaker mode enabled (CN7)

Pins 1 & 2 closed

Pins 1 & 2 closed

Line out function enabled

Pins 2 & 3 closed

Pins 2 & 3 closed

 

 

 

 

 

 

 

 

 

 

 

SUPPORTED COMMAND SET

Basic AT Commands

AT, A/

A, B, C, D, E, H, M, O, P, Q, T, V, W, X, Y, Z

&C, &F, &P, &Q, &R, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \K, \N, \V,

%C, %E, %L, %Q, %TT

S Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25,

S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91,

S92, S95

Special Commands

#CID, +MS, #BDR, #CLS, MDL?, #MFR?, #REV?, #TL, #VBQ?, #VBS, #VBT, #VCI?, #VLS, #VRA, #VRN,

#VRX, #VSD, #VSK, #VSP, #VSR, #VSS, #VTD, #VTM, #VTS, #VTX

Note: See MHI Help File for full command documentation.

Proprietary AT Command Set

AUTO-MODE DETECTION

Type:

Configuration

Format:

AT [cmds] Nn [cmds]

Description:

Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed.

Command

Function

N0

Auto-mode detection disabled

N1

Auto-mode detection enabled

CLOCK SOURCE - SYNCHRONOUS TRANSMIT

Type:

Configuration

Format:

AT [cmds] &Xn [cmds]

Description:

Selects DTE transmit clock source

Command

Function

&X0

Modem generates clock

&X1

Modem generates clock from the receive carrier signal

COMMUNICATIONS MODE

Type:

Configuration

Format:

AT [cmds] &Mn [cmds]

Description:

Selects communications mode

Command

Mode

&M0

Asynchronous mode

&M1

Synchronous connect mode and asynchronous off-line command mode.

&M2

Synchronous connect mode and asynchronous off-line command mode and set DTR high.

&M3

Synchronous connect mode and asynchronous off-line command mode and set DTR to low.

DATA SET READY (DSR)

Type:

Configuration

Format:

AT [cmds] &Sn [cmds]

Description:

Selects DSR options

Command

Function

&S0

DSR forced high

&S1

DSR high only while modem is handshaking or connected

DATA TERMINAL READY (DTR)

Type:

Configuration

Format:

AT [cmds] &Dn [cmds]

Description:

Selects modem response to DTR

Note: The action each variant of &D causes depends on the setting of &Q

&Q Setting

&D0

&D1

&D2

&D3

&Q0, &Q5, &Q6

Command 0

Command 1

Command 2

Command 3

&Q1, &Q4

Command 2

Command 1

Command 2

Command 3

&Q2, &Q3

Command 2

Command 2

Command 2

Command 2

Command

Function

Command 0

Modem does not respond to DTR

Command 1

Modem goes to command mode after DTR goes is off

Command 2

Modem goes to command mode and disconnects (hangs up) after DTR goes off.

Command 3

Modem is initialized after DTR goes off

FLOW CONTROL

Type:

Configuration

Format:

AT [cmds] &Kn [cmds]

Description:

Enables flow control options

Command

Function

&K0

Flow control disabled

&K3

RTS/CTS and DTE/DCE flow control enabled

&K4

XON/XOFF and DTE/DCE flow control enabled

&K5

Transparent XON/XOFF flow control enabled

&K6

RTS/CTS and XON/XOFF flow control enabled

GUARD TONE

Type:

Configuration

Format:

AT [cmds] &Gn [cmds]

Description:

Commands the modem to transmit a guard tone in V.22/V.22bis

Note: Used primarily for international data transmission

Command

Function

&G0

Guard tone disabled

&G1

Guard tone disabled

&G2

1800Hz guard tone enabled

 

 

 

 

 

REPORT INFORMATION

Type:

Immediate

Format:

AT [cmds] In [cmds]

Description:

Displays information requested

Command

Function

I0

Reports modem model and speed

I1

Reports ROM checksum

I2

Reports OK

I3

Reports firmware revision, model and interface type

I4

Reports response programmed by OEM

I5

Reports the country code parameter

I6

Reports modem data pump model and code revision

SPEAKER VOLUME

Type:

Configuration

Format:

AT [cmds] Ln [cmds]

Description:

Controls speaker volume

Command

Function

L0

Low volume setting

L1

Low volume setting

L2

Medium volume setting

L3

Highest volume setting

TEST MODES

Type:

Immediate

Format:

AT [cmds] &Tn

Description:

Selects test options

Command

Function

&T0

End current test

&T1

Begin local analog loopback test

&T2

Returns error result code

&T3

Begin local digital loopback

&T4

Grant remote digital loopback request

&T5

Deny remote digital loopback request

&T6

Request remote digital loopback

&T7

Request remote digital loopback and self-test

&T8

Begin local analog loopback and self-test

S(status) -REGISTERS

AUTOSYNC OPTIONS

Type:

Register

Format

AT [cmds] S19=n

Default:

0

Description:

Enables selection of the autosync options

 

 

AUTOSYNC OR BSC SYNC ENABLED

Type:

Register

Format

AT [cmds] S20=n

Default:

0

Description:

Enables autosync HDLC address or BSC sync characters