D S P - 3 0 5 3 L DEC NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 3117| | | Capacity form/unform 535/ 684 MB Heads 4| | | Seek time / track 9.5/ 1.0 ms Sector/track | | | Controller SCSI2 SI/FAST Precompensation Cache/Buffer 512 KB SEGMENTED Landing Zone Data transfer rate 4.000 MB/S int Bytes/Sector 512 10.000 MB/S ext SYNC Recording method RLL 1/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 66 Power: sleep W Humidity % 10 90 | 8 95 standby W Altitude km -0.061 3.048| 12.192 idle 7.5 W Shock g 10 | 45 seek 9.0 W Rotation RPM 5400 read/write W Acoustic dBA 34 spin-up W ECC Bit 264 MTBF h 500000 Warranty Month Lift/Lock/Park YES Certificates CSA,FCC,TUV,UL1950,VDE ********************************************************************** L A Y O U T ********************************************************************** DEC DSP3000L/LD SERIES PRODUCT DESCRIPTION EK-RH3CA-PD.A01 50-pin SCSI Connector (8-bit) ----------------------------- +------------------------------------+ | Back View | | | +------------J1----------------J2----+ |+------------ ------------++-------+| ||oooooooooooooooooooooooo1||O O O O|| ||oooooooooooooooooooooooo2|| || |+-------------------------++-------+| +-----------SCSI-------------Power---+ + + +------------------------------------+ | Front View (Bezel End) | | | | Fault LED | +-+----------------------------------+ +-++----------+----------------------+ | ||ooo oooooo20 | + ||oooooooooo| + |+1---------J3 Option Busy LED Connector +---------------------------------------------------------+ | Termination ++ |XX J1 | Header ++ |XX | |XX | |XX I | |XX N | |XX T | |XX E | |XX R | |XX F | |XX A | |XX C |+-+J3 Option |XX E || | Connector |1X || | | |+-+ |XX J2 |* Busy LED |XX Power +---------------------------------------------------------+ ********************************************************************** J U M P E R S ********************************************************************** DEC DSP3000L/LD SERIES INSTALLATION GUIDE EK-RH3CA-IG.A01 Jumper Setting ============== TERMPWR (Terminator Power) -------------------------- Generally, the host is the only device on the SCSI bus required to provide TERMPWR for the bus. To ensure that there is a sufficient level of power along the entire SCSI bus, Digital Equipment Corporation recommends that all devices on the SCSI bus supply TERMPWR (if they are capable). SCSI devices are protected by a diode or similar semiconductor to prevent back flow of the terminator power when more than one device supplies this power. NOTE LR Models do not provide TERMPWR to the SCSI bus. The RAID connector does not accommodate this feature. TERMPWR L/LD Models ------------------- ++ | To provide TERMPWR, install the ++ | TERMPWR jumper at the following | ++ | locations. | ++ | | | | +-----------------------+------+ XXXX XXXXXXXXXXXXXXXXXXXXXXXXX SCSI Connector | +--------------------+ +--+ |xx| Drive provides TERMPWR to SCSI bus and active termination |oo| disabled. |oo| +--+ | +--+ |oo| Drive does not provide TERMPWR to SCSI bus and active |oo| termination enabled. |xx| +--+ | +--+ |xx| Drives provides TERMPWR to SCSI bus and active termination |oo| enabled. |xx| +--+ | +--+ |oo| Drive does not provide TERMPWR to SCSI bus and active |oo| termination disabled. |oo| +--+ SCSI Bus Termination -------------------- Both ends of the SCSI bus cable must be terminated. One end is terminated at the host. The other end must be terminated by the last SCSI device on the SCSI bus. Drive Termination ----------------- DSP3000L Series drives contain internal components to provide active termination of the SCSI bus. When this drive is the last device on the SCSI bus, configure the drive to enable active termination. Do so by installing a shunt jumper at the drive's active termination header. If active termination is not required for this drive, make sure that the jumper is not installed. SCSI ID (Address) Selection --------------------------- Each device on the SCSI bus must have a unique SCSI ID number assigned to it. ID number for L/LD models (8-bit SCSI) range from 0 through 7. For LW/LWD models (16-bit SCSI), the numbers range from 0 through 15. SCSI ID numbers for LR models range from 0 through 7 for 8-bit configurations and from 0 through 15 for 16-bit configurations. Configure the SCSI ID of L/LD/LW/LWD models by installing jumper across the indicated Option connector pins. For LR versions, provide the proper open or ground signal input to the referenced pins of the drive's 80-pin RAID connector. SCSI ID - L/LD Models --------------------- +----------+-----------------------+ +2--------20 | SCSI ID | Jumper Location | |ooo oooooo| Option | | PINS | |oooooooooo| Connector | | 5-6 | 3-4 | 1-2 | +1---------+ +----------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | | 1 | OPEN | OPEN | CLOSED| | 2 | OPEN | CLOSED| OPEN | | 3 | OPEN | CLOSED| CLOSED| | 4 | CLOSED| OPEN | OPEN | | 5 | CLOSED| OPEN | CLOSED| | 6 | CLOSED| CLOSED| OPEN | | 7 | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+ Configure Optional Features --------------------------- CAUTION The 5-volt signals of two or more drives should not be connected together or to any other current source by using the Option connector. Doing so may cause drive malfunction or component damage. Except when connecting several drives together for a spindle synchronization application, do not connect the ground signals of two or more drives together or to any other current source using the Option connector. Doing so may introduce ground loop problems. The following optional features can be configured according to your system requirements. These features (model-dependent) include: - Notification of AC power failure (not currently supported by LR models. SCSI RST may be used instead.) - Spindle synchronization - Write protection (not currently supported by LR models) - Spin delay AC Failure Notification ----------------------- The AC Low connection (AC_LOW L) is not currently supported on LR models, SCSI Bus Reset provides the alternative to the AC Low warning. The host system or power supply can warn the drive of an impending AC failure by asserting the signal AC_LOW L. This is an active low signal (low means power failure). NOTE The system should provide this warning at least 10 milliseconds prior to failure for this feature to be operational. To utilize the AC-LOW L warning feature, connect the system's AC power warning signal and associated ground to the referenced AC_LOW L and ground pins on the Option connector. When the host system assert the AC_LOW L warning to the drive, the drive prevents write-spliced for outstanding writes. AC_LOW L Connection ------------------- DSP3053L +---- LOGIC_GND L DSP3053LD +-------+-20 DSP3107L |ooo ooo*oo|Option Connector DSP3107LD |ooooooo*oo| DSP3133L +1------+--+ DSP3133LD +---- AC_LOW L Spindle Synchronization ----------------------- DSP3000L Series drives support synchronized spindle operation. Master or slave synchronized operation is set through a SCSI Mode Select Page. When the drive operates as a Master, it generates a spindle synchronization reference signal (SPINDLE_SYNC_REF L). When operating as a slave, the drive synchronizes its spindle according to the SPINDLE_SYNC_REF L input reference. The drive always maintains local speed regulation when no reference signal is applied. NOTE The reference signal must originate from drives with the same electronics modules. Fo example, connect Model DSP3107L only with another DSP3107L drive. Do not connect the SPINDLE_SYNC_REF L signal so that of any other model disk drive. Otherwise, the drive may mal- function. When connecting multiple drives together for spindle synchronization, be sure to use proper cabling techniques to avoid ground loop problems. Spindle Sync Connection ----------------------- The following figure shows the SPINDLE_SYNC_REF L connection pin (and associated ground) for DSP3000L Series drives. DSP3053L Option Connector DSP3053LD +---------20 DSP3107L |*** @oooo*| * = LOGIC_GND L (Pins 2,4,6,20) DSP3107LD |ooooooooo@| @ = SPINDLE_SYNC_REF L (Pins 10,19) DSP3133L +1---------+ DSP3133LD For L/LD models, pin 10 is provided as an alternate SPINDLE_SYNC_REF L connection to facilitate installations where a 10-pin header is used to connect several remote features. Pin 19 is provided to facilitate the use of a 2-pin connector for SPINDLE_SYNC_REF L connections. The ground return is pin 20, although pins 2, 4, or 6 can be used for the ground return. Write Protection ---------------- L/LD/LW/LWD models support either the Write Protect or Spin Delay mode. If your drive supports the Write Protect mode, provide write protection by installing the jumper across the referenced pins of the Option connector. To disable Write Protection from L/LD model drives, remove the jumper from across 13 and 14 of the Option connector. Note that when the Write Protect Mode bit is set to a 1, automatic spin up occurs at power on. DSP3053L +---------20 DSP3053LD |ooo ooXooo|Option Connector DSP3107L |ooooooXooo| DSP3107LD +1---------+ DSP3133L DSP3133LD Spin Delay ---------- The method for establishing spin-up characteristics is dependent upon the drive model. Spin Delay - L/LD/LW/LWD Models ------------------------------- These drives support either the Write Protect or Spin Delay mode. If your drive supports the Spin Delay mode, you can program the drive automatically spin-up at powere on by installing the jumper across the referenced Option connector pins. To have spin-up controlled by a Start/Stop Unit command, remove the jumper. DSP3053L +---------20 DSP3053LD |ooo ooXooo|Option Connector DSP3107L |ooooooXooo| DSP3107LD +1---------+ DSP3133L DSP3133LD Remote Features --------------- DSP3000L Series drives support the following remote features, which can be configured at the drive's Option connector or RAID backplane: - Remote SCSI ID selection - Remote LED status display Remote SCSI ID Selection ------------------------ SCSI ID can be set remotely from an external (remote) switch or control panel. For L/LD/LW/LWD models, this is accomplished using the Option connector. For LR models, the output of the remote or external ID switches takes the place of jumpers or circuits at the RAID system backplane. Configure L/LD/LW/LWD models for remote ID selection by removing the SCSI ID jumpers (if present) fromn the SCSI ID pins. Then connect the leads from the external selection switch to the referenced pins. Observe the following guidelines while doing so. - ID bit 0, at Pin 1, is the Least Significant Bit. - SCSI ID bits 0, 1, 2, and 3 are active LOW signals. That is, the bit is a 1 if the corresponding remote switch is closed to ground. - For L/LD models, use pins 2, 4, and 6 as the associated ground re- turns for ID bits 0, 1, and 2 respectively. They can be used individually, or the ground returns of all three ID bits can be combined at pin 2, 4, or 6. Option Connector DSP3053L +---------20 DSP3053LD |*** oooooo| * = LOGIC_GND L (Pins 2,4,6) DSP3107L |@@@ooooooo| @ = SCSI ID <0>,<1>,<2>, L DSP3107LD +1---------+ (Pins 1,3,5) DSP3133L DSP3133LD Remote LED Status Display ------------------------- Busy and Fault status for L/LD/LW/LWD models can be monitored by connecting a remote Busy and a remote Fault display LED to the drive's Option connector. Remote Busy - L/LD/LW/LWD Models -------------------------------- The remotely monitor Busy status of the drive, connect the cathode side of the remote Busy LED to the BSY_OUT L pin. The anode side of the LED connects to the +5 VDC OUT pin. Remote Fault - L/LD/LW/LWD Models --------------------------------- The remotely monitor Fault status of the drive, connect the cathode side of the remote Fault LED to the FLT_OUT pin. The anode side of the LED connects to the +5 VDC OUT pin. Option Connector DSP3053L +---------20 DSP3053LD |ooo oooooo| DSP3107L |ooo***oooo| DSP3107LD +1--+++----+ DSP3133L ||+-- +5 VDC OUT DSP3133LD |+--- BSY_OUT L +---- FLT_OUT L ********************************************************************** I N S T A L L ********************************************************************** DEC DSP3000L SERIES INSTALLATION GUIDE EK-RH3CA-IG.A01 Notes on installation ===================== Drive mounting -------------- horizontally vertically +-----------------+ +--+ +--+ +------------------+ | | | +-----+ +-----+ | | | | | | | | | | | |+----------------+| +-+-----------------+-+ | | | | | | || || +---------------------+ | | | | | | || || | | | | | | || || | | | | | | || || +---------------------+ | +-----+ +-----+ | || || +-+-----------------+-+ +--+ +--+ || || | | || || | | || || +-----------------+ || || ++----------------++ You can mount the disk drive in any position. LR models mount in RAID storage subsystems. The drive (with bezel) attaches to the system bay and accept #6-32 screws. Screws should not exceed 0.25 inch (6.25 millimeters) in length, otherwise damage to the PCB may result. Mounting and Bezel Options -------------------------- Bezels and mounting brackets are available from Digital Equipment Corporation for mounting the drive in either 3.5-inch or 5.25-inch form factor bays. Combination Connector - L/LD Models ----------------------------------- +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-36486-01 | Digital Equipment Corp. | +-----------------+-----------------------------------------------+ | 89331-001 | Berg Electronics (formerly Dupont Electronics)| +-----------------+-----------------------------------------------+ | CWN-710-54-0119 | C.W. Industries | +-----------------+-----------------------------------------------+ | DA-2339-25 | Methode Electronics | +-----------------+-----------------------------------------------+ Includes 0.1-in pitch, 50-pin SCSI connector and 4-pin power connector. Combination Connector - LW/LWD Models ------------------------------------- +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-40413-01 | Digital Equipment Corp. | +-----------------+-----------------------------------------------+ | 92-1814-12-1 | AMP, Inc. | +-----------------+-----------------------------------------------+ Includes 68-pin SCSI connector, 4-pin power connector, and a 2-mm pitch, 12-pin (2x6) Option connector. Option Connector - L/LD Models ------------------------------ +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-36484-02 | Digital Equipment Corp. | +-----------------+-----------------------------------------------+ | 90516-003 | Berg Electronics (formerly Dupont Electronics)| +-----------------+-----------------------------------------------+ | 3-176837-3 | AMP, Inc. | +-----------------+-----------------------------------------------+ | 87049-2091 | Molex, Inc. | +-----------------+-----------------------------------------------+ A 2-mm pitch, 19-pin (2x10) keyed (missing pin) connector Secondary Option Connector - LW/LWD Models ------------------------------------------ +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-36484-05 | Digital Equipment Corp. | +-----------------+-----------------------------------------------+ A 2-mm pitch, 5-pin (2x3) keyed (missing pin) connector Shunt Jumper - All Models ------------------------- +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | 12-36482-01 | Digital Equipment Corp. | +-----------------+-----------------------------------------------+ | 86730-001 | Berg Electronics (formerly Dupont Electronics)| +-----------------+-----------------------------------------------+ | LPC-SPG | Honda | +-----------------+-----------------------------------------------+ A 2-mm pitch shunt for configuring termination characteristics RAID Connector - LR Models -------------------------- +-----------------+-----------------------------------------------+ | Part Number | Vendor | +-----------------+-----------------------------------------------+ | TBS | Digital Equipment Corp. | +-----------------+-----------------------------------------------+ DC Power and pin connector assignments -------------------------------------- +------------+ pin 1 +12 VDC | 4 3 2 1 | pin 2 +12 Volts Return GROUND +------------+ pin 3 + 5 Volts Return GROUND pin 4 + 5 VDC ********************************************************************** F E A T U R E S ********************************************************************** DEC DSP3000L SERIES INSTALLATION GUIDE EK-RH3CA-IG.A01 Product Summary --------------- DSP3000L Series 3.5-inch Disk Drives are high-performance, high capacity drives, designed and manufactures by Digital Equipment Corporation. Features -------- Features of the DSP3000L Series drives include the following: - Formatted capacity ranging from 535 MB to 1,377.5 MB, depending upon model - 1 millisecond track-to-track seek time - 512 KB segmented cache buffer - End-to-end Error Detection Code/Parity on cache RAM - Four headers per sector - Embedded quadrature servo - Self-diagnostics - Down-loadable SCSI firmware - Tagged command queuing - Seek ordering - Automatic block realloction - Glitch-free power on/off operation - Synchronized spindle operation - Low power consumption Power-On Tests -------------- After power is applied, and before spin-up is completed, the drive performs self-test diagnostics prior to making itself visible on the SCSI bus. These intitial self-test check most of the electronics that control HDA, but not the SCSI transceiver or SCSI connector. After spin-up, additional tests complete self-test coverage of the electronics module and the HDA. The unit appears not ready to the host between completion of the initial self-tests and completion of the drive's post spin-up tests. Seek Time --------- +----------------------------------+--------+--------+--------+ | |DSP3053L|DSP3107L|DSP3133L| +----------------------------------+--------+--------+--------+ |Track-to-Track msec. typ. | 1 | 1 | 1 | +----------------------------------+--------+--------+--------+ |Average msec. typ. | 9.5 | 9.5 | 9.5 | | msec. max. | 20 | 20 | 20 | +----------------------------------+--------+--------+--------+ |Latency msec. avg. | 5.6 | 5.6 | 5.6 | +----------------------------------+--------+--------+--------+ LED Indicators -------------- The green Busy LED illuminates to signify the drive is working on a SCSI command. The amber Fault LED indicates a fault status. Both the Busy and Fault indicators light briefly during power up. This serves as a hardware and lamp test. During a calibration operation, the Busy LED is illuminated and the Fault LED flashes. Calibrations occur following some firmware up- grades. Generally, calibration periods last only about five minutes, after which the drive comes on-line and both indicators go out. If the Fault indicator lights at any other time, the drive has failed and likely requires service (unless the Fault LED was turned on by means of a MODE SELECT command). Remote Busy and Fault indicators can be connected to the Option connector to provide status display at a remote location or panel.