9 1 1 9 0 D 7 D I A M O N D M A X MAXTOR Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders | | | Capacity form/unform 11900/ MB Heads 7| | | Seek time / track 9.0/ 0.9 ms Sector/track | | | Controller IDE / ATA4 ULTRA Precompensation Cache/Buffer 256 KB SDRAM Landing Zone Data transfer rate 18.600 MB/S int Bytes/Sector 512 33.000 MB/S ext Recording method operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 55 | -40 71 Power: sleep W Humidity % 5 95 | 5 95 standby 0.9 W Altitude km -0.061 3.048| -0.061 12.192 idle 4.4 W Shock g 20 | 200 seek 9.6 W Rotation RPM 5400 read/write 4.8 W Acoustic dBA 36 spin-up 20.2 W ECC Bit MTBF h 500000 Warranty Month 36 Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** MAXTOR DIAMOND MAX 3400 Pin 1 J1 IDE Connector | J2 Power +----------- --------+-++-----------++---------+ | .................... || @ * * * || X X X X | | .......... ......... || @ * * * * || X X X X | +----------------------++-+-+-+-+-+-++-+-+-+-+-+ | | | | | | | | | | | | | | | | | | J50 Master/Slave -----+ | | | | | | | +-+12V J48 Cable Select -------+ | | | | | +---+12V Return J46 4092 Cyl Limitation---+ | | | +----- +5V Return J44 Factory Reserved -------+ | +------- +5V J42 Factory Reserved ---------+ ********************************************************************** J U M P E R S ********************************************************************** MAXTOR DIAMOND MAX INSTALLATION SHEET Jumper Setting ============== +---+---+---+---+---+ |J50|J48|J46|J44|J42| +-------------------------------------+---+---+---+---+---+ | Master/Slave | | | | | | | Only Drive in single drive system* | J | | | | | +-------------------------------------+---+---+---+---+---+ | Master in a dual drive system* | J | | | | | +-------------------------------------+---+---+---+---+---+ | Slave in a dual drive system | O | | | | | +-------------------------------------+---+---+---+---+---+ | Cable Select | | | | | | | Disabled* | | O | | | | +-------------------------------------+---+---+---+---+---+ | Enabled | | J | | | | +-------------------------------------+---+---+---+---+---+ J=Jumpered O=Open *=Default ********************************************************************** I N S T A L L ********************************************************************** MAXTOR 91360D8/91190D7/91020D6/90845D5/90680D4/90510D3/90340D2 Notes on installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ The drive will operate in all axis (6 directions). Idle The drive is spinning., the actuator is parked and powered off, and all other circuitry is powered on. The drive is capable of responding to read commands within 40 ms. Read/Write Data is being read from or written to the drive. Spin-up The drive is spinning up following initial application of power and has yet not reached full speed. Maximum current draw lasts one second. Standby The spin motor is not spinning. The drive will leave this mode upon receipt of a command that requires disk access. The time-out value for this mode is programmable. The buffer is active to accept write data. Sleep This is the lowest power state - with the interface set to inactive. A software or hardware reset is required to return the drive to the standby state.