S D - 3 8 0 H - 0 0 TEAC NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 3.5"/SLIMLINE Cylinders 1050| | | Capacity form/unform 86/ MB Heads 4| | | Seek time / track 19.0/ 8.0 ms Sector/track 40| | | Controller SCSI1 SINGLE-ENDED Precompensation Cache/Buffer 62 KB Landing Zone Data transfer rate 1.500 MB/S int Bytes/Sector 512 1.500 MB/S ext ASYNC Recording method RLL 2/7 operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 5 50 | -40 60 Power: sleep W Humidity % 8 80 | 8 80 standby 0.3 W Altitude km -0.300 3.000| -0.300 12.000 idle 3.4 W Shock g 5 | 60 seek 5.5 W Rotation RPM 3600 read/write 3.7 W Acoustic dBA 50 spin-up W ECC Bit MTBF h 30000 Warranty Month Lift/Lock/Park - Certificates CSA,TUV,UL478,VDE ********************************************************************** L A Y O U T ********************************************************************** TEAC SD-380H-00 SPECIFICATION REV. A, P/N 10530579-00 +---------------------------------------------------------++-+Strap | || |SP | |+-+S0 3 | |XX1 | |XX Inter- | |XX face | |XX | |XX | |XX |++LED |XX |++ |XX | |XX | |XX | |XX | | | |XX Power | |XX +---------------------------------------------------------+ 4 ********************************************************************** J U M P E R S ********************************************************************** TEAC SD-380H-00 SPECIFICATION P/N 10530579-00 REV. A Jumper Setting ============== Strap +-------+ +------------------------1+ +-----+ |4 3 2 1| |:::::::::::::::::::::::::| |ooooo| PCB---+-------+-+------------------------2+-+-----+ Power Interface ||||| S3+|||+SP S2-+|+-S0 S1 Indicator --------- The indicator on the front bezel shall be kept lit after the HDD responds to a selection from an initiator, and before it completes the execution of the command. Parity Strap ------------ The S3 on the PCBA is used asa parity strap. When the S3 is shorted with a plug, the input data (DB0 to DB7, DBP) shall be parity checked (odd) by the HDD. When the S3 is open, no parity check shall be executed. Factory setting: S3 shorted. How to Set the SCSI ID ---------------------- The SCSI ID shall be set with the individual straps of SP, S0, S1, and S2 on the PCBA. The SP strap is to reserve the setting logic for S0, S1 and S2. +----------+---------------+----------------+ | | SP=ON | SP=OFF | +----------+---------------+----------------+ |SCSI ID | S2 S1 S0 | S2 S1 S0 | +----------+---------------+----------------+ | 0 | ON ON ON | OFF OFF OFF |Factory Setting +----------+---------------+----------------+ | 1 | ON ON OFF | OFF OFF ON | +----------+---------------+----------------+ | 2 | ON OFF ON | OFF ON OFF | +----------+---------------+----------------+ | 3 | ON OFF OFF | OFF ON ON | +----------+---------------+----------------+ | 4 | OFF ON ON | ON OFF OFF | +----------+---------------+----------------+ | 5 | OFF ON OFF | ON OFF ON | +----------+---------------+----------------+ | 6 | OFF OFF ON | ON ON OFF | +----------+---------------+----------------+ | 7 | OFF OFF OFF | ON ON ON | +----------+---------------+----------------+ Note: The strap states are as follows: 1: Strap open 2: Strap short Terminator factory setting: equipped ********************************************************************** I N S T A L L ********************************************************************** TEAC SD-380H-00 SPECIFICATION P/N 10530579-00, REV. A Notes on Installation ===================== Installation direction ---------------------- horizontally vertically +-----------------+ +--+ +--+ | | | +-----+ +-----+ | | | | | | | | | +-+-----------------+-+ | | | | | | +---------------------+ | | | | | | | | | | | | | | | | | | +---------------------+ | +-----+ +-----+ | +-+-----------------+-+ +--+ +--+ | | | | +-----------------+ Any of the four directions can be used. The mounting cabinet for the HDD should be constructed so that no distortion may be produced in the chassis. A space of at least 1.5mm should also be allowed each of the HDA and PCBA. An insulation sheet should be stuck to the PCBA mounting face of the HDD mounting cabinet, as required. In each mounted position, the front can be raised by up to 30*. Mounting positions other than those shown must be discussed separately. Screws ------ Tapped holes for installation each side: 3-M3 4 deep Tapped holes for installation bottom: 4-M3 4 deep Screws: M3 x 10 Front Bezel ----------- Not equipped LED Indicator color ------------------- Green Power Interface Connectors -------------------------- HDD Side Connector AMP P/N 171826-4 (natural color) or equivalent Number of pins 4 Prevention method for mis-connection Mechanical protection of the shape of the connector housing Cable side matched connector AMP P/N 171822-4 (natural color) or equivalent Matched pin AMP P/N 170204-2 (AWG 20 to 26, loose piece) or P/N 170262-2 (AWG 20 to 26, chained form), or equivalent Power cable The maximum power consumption of the HDD and the voltage at the power connector shall be taken into consideration. Power interface connector pin number ------------------------------------ pin 4 +12 VDC pin 3 0 Volt pin 2 0 Volt pin 1 + 5 VDC Electrical Characteristics -------------------------- All the following specification apply to the interface connector of the HDD. The input signal metioned below means the signal provided to the HDD, and the output signal means the signal output from the HDD. 1. Input signal a. Receiver: CMOS receiver with hysteresis b. Input signal level i. Low level (true): 0 0.8 VDC ii. High level (false): 2.0 5.25 VDC c. Maximum load current: 10 A (excluding the terminator) d. Minimum hysteresis width: 0.2 VDC 2. Output signal a. Driver: Open-drain type CMOS driver b. Output signal level with the terminator connected i. Low level (true): 0 0.5 VDC ii. High level (false): 2.4 5.25 VDC c. Driver sink current: 48mA (low-level voltage: 0.5 VDC) 3. TERMPWR signal a. Output voltage: 4.0 5.25 VDC b. Maximum output current: 1.0A c. Output current limitation: Fuse (1.0A) 4. Terminator (effective for the 18 signals except for the TERMPWR signal) a. Terminator block: 11-pin SIP type x 2 pcs, detachable b. Resistance values i. +5V side: 220 5% ii. 0V side: 330 5% Signal Interface Connector and Cable ------------------------------------ 1. Signal interface connector: a. HDD side connector: Du Pont Electronics 68020-550 b. Number of pins and pitch: 2.54 (0.1 in) pitch, 50-pin pin block header (25 pins in each of 2 rows with oddnumbered pins on the top face of HDD) c. Cable side matched connector: Du Pont Electronics 66902-050 2. Signal interface cable a. Type: 50-core flat cable or 25-pair twisted cable b. Conductor size: AWG 28 or more Equivalent parts may be used. 3. Characteristic impedance: 100 10% (recommended) (When daisy chain is to be performed, match the characteristic impedances of individual cables which each other.) 4. Maximum cable length: 6 meters System Configuration -------------------- Up to eight SCSI devices can be connected to the SCSI bus, including initiators and targets. The SCSI devices mean devices provided with interfaces which comply with the SCSI standard. The HDD is always operated as a target, and it can be used in any configuration (a, b, c). The SCSI devices are allocated with SCSI IDs, which correspond to the individual bits of the data bus. With the HDD, SCSI IDs are set by strap connections on the PCB. The priority is determined among the SCSI IDs; SCSI ID = 7 is the highest priority, and SCSI ID = 0 is the lowest priority. a. Single Initiator, Single Target Initiator Target +-------+ +-------+ | HOST +----SCSI-Bus--------+ HDD | | +--------------------+ | +-------+ +-------+ b. Single Initiator, Multiple Targets Initiator Target +-------+ +-------+ | HOST +----SCSI-Bus--------+ HDD | | +------+ +----------+ | +-------+ | | +-------+ | | +-------+ | +----------+OTHER |Target | +----------+DEVICE | | | +-------+ | | +-------+ | +----------+OTHER |Target +-------------+DEVICE | +-------+ c. Multiple Initiators, Multiple Targets Initiator Target +-------+ +-------+ | HOST +----SCSI-Bus--------+ HDD | | +------+ +----------+ | +-------+ | | +-------+ +-------+ | | +-------+ | HOST +------+ +----------+OTHER |Target | +------+ +----------+DEVICE | +-------+ | | +-------+ Initiator | | +-------+ | +----------+OTHER |Target +-------------+DEVICE | +-------+ ********************************************************************** F E A T U R E S ********************************************************************** TEAC SD-380H-00 SPECIFICATION P/N 10530579-00, REV. A Seek Time --------- +----------------------------------+--------+ | |380H-00 | +----------------------------------+--------+ |Track-to-Track msec. typ. | 8 * | +----------------------------------+--------+ |Average msec. typ. | 19 * | | msec. max. | 50 * | +----------------------------------+--------+ |Latency msec. avg. | 8.33 | +----------------------------------+--------+ * = including settling time Adaptable standards ------------------- ANSI Standard X3.131-1986 "SCSI (level 2) ANSI Standard X3T9.2/85-52 Rev 4.B "CCS" Driver/Receiver --------------- Single-ended type Bus parity ---------- Output data from the HDD: Parity is always added (odd parity) Input data to the HDD: Parity check (odd parity) function is optional by the strap connection in the HDD. Data transfer system -------------------- Asynchronous data transfer Sense data ---------- The HDD shall be provided with Extended Sense Data format only. VLD (Valid) The VLD specifies whether or not the Information Byte is valid. When the VLD is one (1), it indicates that the Information Byte is valid. ERROR CLASS The Error Class is always set to "7", which indicates that the Sense Data is the Extended Sense Data. ERROR CODE The error code is always set to zero (0), which indicates that the Sense Data is described in the Extended Data format. SENSE KEYS The Sense Keys indicate the outline of error contents. ADDITIONAL SENSE LENGTH The Additional Sense Length specifies the number of Additional Sense Bytes to follow. This is set to 0BH in the HDD. ADDITIONAL SENSE CODE The Additional Sense Code indicates error coded information. Sense data (Extended) --------------------- +------+------+------+------+------+------+------+------+------+ |Byte |bit 7 |bit 6 |bit 5 |bit 4 |bit 3 |bit 2 |bit 1 |bit 0 | +------+------+------+------+------+------+------+------+------+ | 0 |VLD |ERROR CLASS |ERROR CODE | | +------+------+------+------+------+------+------+------+ | | |1 |1 |1 |0 |0 |0 |0 | +------+------+------+------+------+------+------+------+------+ | 1 |RESERVED | | +------+------+------+------+------+------+------+------+ | |0 |0 |0 |0 |0 |0 |0 |0 | +------+------+------+------+------+------+------+------+------+ | 2 |RESERVED |SENSE KEY | | +------+------+------+------+------+------+------+------+ | |0 |0 |0 |0 | | | | | +------+------+------+------+------+------+------+------+------+ | 3 |INFORMATION BYTE (MSB) | +------+-------------------------------------------------------+ | 4 |INFORMATION BYTE | +------+-------------------------------------------------------+ | 5 |INFORMATION BYTE | +------+-------------------------------------------------------+ | 6 |INFORMATION BYTE (LSB) | +------+-------------------------------------------------------+ | 7 |ADDITIONAL SENSE LENGTH | | +------+------+------+------+------+------+------+------+ | |0 |0 |0 |0 |1 |0 |1 |1 | +------+------+------+------+------+------+------+------+------+ | 8-11 |00H RESERVED (4 BYTES) | +------+-------------------------------------------------------+ |12 |ADDITIONAL SENSE CODE | +------+-------------------------------------------------------+ |13-18 |00H RESERVED (6 BYTES) | +------+-------------------------------------------------------+