H P 9 7 5 4 0 P HEWLETT PACKARD NO MORE PRODUCED Native| Translation ------+-----+-----+----- Form 5.25"/FH Cylinders | | | Capacity form/unform / MB Heads | | | Seek time / track / ms Sector/track | | | Controller SCSI1 SINGLE-ENDED Precompensation Cache/Buffer KB Landing Zone Data transfer rate MB/S int Bytes/Sector 512 MB/S ext Recording method RLL operating | non-operating -------------+-------------- Supply voltage 5/12 V Temperature *C 50 | -40 65 Power: sleep W Humidity % 8 80 | 5 80 standby W Altitude km -0.305 3.048| -0.305 15.240 idle 22.0 W Shock g 5 | 30 seek 34.0 W Rotation RPM read/write W Acoustic dBA spin-up W ECC Bit MTBF h Warranty Month Lift/Lock/Park YES Certificates ********************************************************************** L A Y O U T ********************************************************************** HEWLETT HP 97540T/P DISK DRIVE INSTALLATION GUIDELINES 5960-0111 +---------------------------------------------------------+ | +1|1X | Terminator |||XX SCSI | Packs ++|XX Con. | +1|XX J1 | |||XX | ++|XX | +1|XX | |||XX | ++|XX | |XX | |+-9 | || |Option | || |Con. | || 1 | |2-1 | |XX | |XX Power +---------------------------------------------------------+ 1 | | | ++Frame Ground | ++----------++------------------------------------------------+-+ +-+DC Power Option Connector SCSI Connector J1 +-+ | +-------+ 2 +-+-+-+-+-+-+-+-+-+ +-------------------------+ | | |O O O O| * | | | | | | | | | | |************************1| | | +1-2-3-4+ * +1+2+3+4+5+6+7+8+9+ |*************************| | |------------1----------------------++------++------++------+-+--| | +------1+------1+------1 | +-- Terminator Packs --+ ********************************************************************** J U M P E R S ********************************************************************** HEWLETT HP 97540T/P DISK DRIVE INSTALLATION GUIDELINES 5960-0111 Jumper Setting ============== Option Connector ---------------- +----------------- Power Termination | +-------------- Unit Attention +++ | +------------ Drive initiation of SDTR message 2 +-+-+-+-+-+-+-+-+-+ * | | | | | | | | | | * +1+2+3+4+5+6+7+8+9+ | | | +-+-+ ++ | | +---- SCSI address Synchronized | +-------- Auto spin up Spindle Pins +---------- Parity Synchronized Spindle -------------------- Pin Signal Name 1 Ground 2 Sync 1,2 Power Termination Option Pins --------------------------------- +------+------+------+---------------------------------------+ |Power |Pin |Pin | | |Option|Set 1 |Set 2 | Description | +------+------+------+---------------------------------------+ | 1 |CLOSED|OPEN | All Drives: | | | | | Drive supplies +5V for on-board | | | | | terminator only | +------+------+------+---------------------------------------+ | 2 |CLOSED|CLOSED| All Drives: | | | | | Drive supplies +5V for on-board | | | | | terminator and Pin 26 of SCSI | | | | | connector (J1). | +------+------+------+---------------------------------------+ | 3 |OPEN |CLOSED| Single Ended Drives: | | | | | Initiator supplies +5V to Pin 26 | | | | | of SCSI connector (J1) for on-board | | | | | terminators. | | | | | Differential Drives: | | | | | Initiator supplies +5V to Pins 25 and | | | | | 26 of SCSI connector (J1) for on-board| | | | | terminators. | +------+------+------+---------------------------------------+ | 4 |OPEN |OPEN | No power supplied by drive to on-board| | | | | terminator, or to PIN 26 of SCSI | | | | | connector. | | | | | | | | | | Power supplied by initiator to PIN 26 | | | | | not connected to on-board terminators.| +------+------+------+---------------------------------------+ 3 Unit Attention ---------------- OPEN Enabled (standard default) CLOSED Disabled 4 Drive initiation of SDTR message ---------------------------------- OPEN Inhibit initiation of SDTR message CLOSED Enable initiation at Power On and RESET 5 Parity -------- OPEN Parity checking is disabled CLOSED Parity checking is enabled 6 Auto spin up -------------- OPEN Drive will not spin up until host sends start unit command CLOSED Drive will automatically spin up on power on 7,8,9 SCSI address ------------------ +----------+-----------------------+ | SCSI ID | Jumpers | | | 7 | 8 | 9 | +----------+-------+-------+-------+ | 0 | OPEN | OPEN | OPEN | +----------+-------+-------+-------+ | 1 | OPEN | OPEN | CLOSED| +----------+-------+-------+-------+ | 2 | OPEN | CLOSED| OPEN | +----------+-------+-------+-------+ | 3 | OPEN | CLOSED| CLOSED| +----------+-------+-------+-------+ | 4 | CLOSED| OPEN | OPEN | +----------+-------+-------+-------+ | 5 | CLOSED| OPEN | CLOSED| +----------+-------+-------+-------+ | 6 | CLOSED| CLOSED| OPEN | +----------+-------+-------+-------+ | 7 | CLOSED| CLOSED| CLOSED| +----------+-------+-------+-------+ DC Power and pin connector assignments -------------------------------------- +------------+ pin 1 +12 VDC | 1 2 3 4 | pin 2 +12 Volts Return +------------+ pin 3 + 5 Volts Return pin 4 + 5 VDC ********************************************************************** I N S T A L L ********************************************************************** HEWLETT HP 97540T/P DISK DRIVE INSTALLATION GUIELINES 5960-0111 Notes on Installation ===================== Drive mounting -------------- horizontally vertically +-----------------+ +--+ +--+ +------------------+ | | | +-----+ +-----+ | | | x | | | | | | | | x+----------------+x +-+-----------------+-+ | | | | | | ||x x|| +---------------------+ | | | | | | || x x || | | | | | | || x x || x x | | | | | | || x x || +------x------x-------+ | +-----+ +-----+ | || xx || +-+------x--x-------+-+ +--+ +--+ || x x || | xx | || x x || | x x | || x x || +---x--------x----+ |x x| x x x++----------------++x UNACCEPTABLE! UNACCEPTABLE! Never install PC board on the Top! DO NOT mount the disk drive in a front-down or back-down position. Use the following guidelines to mount the disk drive: Use 6/32 screws and torque them to 10 inch-pounds. When mounted, the hardware must not penetrate more than 1 mm (0.04 in.) beyond the inside of the disk drive frame. There should be at least 3 mm (0.12 in) clearance around the physical limits of the disk drive to allow for movement of the disk drive frame. There should be at least 3 mm (0.12 in.) clearance around the physical limits of the disk drive to allow for movement of the disk drive under maximum loads.